Recent Content by 93mit

  1. 93mit
    Post

    Mouse smell from vents

    Put a open box, or two, of moth-balls in your truck and that will help keep the mice out...I remove them when I drive mine
    Post by: 93mit, Oct 8, 2014 in forum: Daihatsu Hi jet
  2. 93mit
    Post

    Started my 93 mits lift

    I used wrist pins out of a engine, 1066 IH To make the spacers to lift mine and then used some more of them to drop the crossmember It...
    Post by: 93mit, Mar 3, 2014 in forum: Mitsubishi Minicab
  3. 93mit
    Post

    don't understand lift problems...

    When I lifted mine I used wrist pins from a 1066 IH tractor As spacers, worked great.
    Post by: 93mit, Feb 22, 2013 in forum: Mitsubishi Minicab
  4. 93mit
    Post

    i have a 1987 minicab LHD 2wd 3 speed with a 3g81 engine and need help

    Search the older post this has been covered and you will learn alot of other stuff
    Post by: 93mit, Jun 7, 2012 in forum: Mitsubishi Minicab
  5. 93mit
    Post

    1991 Wont Start??

    Start chasing the spark down, coil, condenser, cap, bug, switch, etc. sorry I can't be more help than that
    Post by: 93mit, Mar 26, 2010 in forum: Mitsubishi Minicab
  6. 93mit
    Post

    My Mini Truck/ Sprint Car Push Truck

    Would make a good BOV
    Post by: 93mit, Mar 22, 2010 in forum: Tips and Tricks
  7. 93mit
    Post

    Engine & Solid Axle Swap Build

    Damn the bad luck
    Post by: 93mit, Feb 8, 2010 in forum: General Truck Info
  8. 93mit
    Post

    mits manual US 550 3g81 lefty

    I had my 3 speed replaced with a 4 speed, I don't regret it one bit.
    Post by: 93mit, Feb 1, 2010 in forum: Mitsubishi Minicab References
  9. 93mit
    Post

    mitsubishi governor

    Don, sorry if I was steering auburn wrong, but I was assuming that his truck was one of the trucks that was gov. to 25 mph. My apologies.
    Post by: 93mit, Dec 31, 2009 in forum: Mitsubishi Minicab
  10. 93mit
    Post

    mitsubishi governor

    PM Dan. He can explain any questions you have, after you have done a search, Dan is the man on the Mits.
    Post by: 93mit, Dec 30, 2009 in forum: Mitsubishi Minicab
  11. 93mit
    Post

    Engine & Solid Axle Swap Build

    Anything is possible with a cutting torch and a welder.
    Post by: 93mit, Nov 10, 2009 in forum: General Truck Info
  12. 93mit
    Post

    Need more speed.

    You have to change the distributor, and not all 3 speeds can be changed into a 4 speed, you might have to get another tranny. Try sending Dan a PM...
    Post by: 93mit, Nov 5, 2009 in forum: Mitsubishi Minicab
  13. 93mit
    Post

    I'm gonna be a dad!!!

    Tax deduction, dependent.
    Post by: 93mit, Oct 30, 2009 in forum: Introductions
  14. 93mit
    Post

    105 amp alternator upgrade

    Did this on a toyota truck one time, worked great.
    Post by: 93mit, Oct 28, 2009 in forum: Tips and Tricks
  15. 93mit
    Post

    I'm gonna be a dad!!!

    Deductions +1
    Post by: 93mit, Oct 19, 2009 in forum: Introductions