Subaru Sambar specs/ interchange part #'s

Factory Head Gasket Part #

OEM Subaru Part # for Head Gasket

Applies to EN07 engine Part # 11044KA211

 

Subaru OEM Brake Rotor part #

Subaru OEM Brake Rotor Part # 26311 - TA001/002

Part # applies to KS3/ KS4/ KV3/ KV4 Sambar

 

More Aftermarket Clutch Part #'s

Asco – Aisin Seiki Brand Clutch Replacement part #'s

CF-006 Pressure Plate

DF-009 Disc

Applies to: KS3 (90 / 3 97 / 5, SPC), KS4 (90 / 3 97 / 5, SPC), KV3 (90 / 3 97 / 5, SPC), KV4 (90 / 3 97 / 5, SPC) cargo compatible stripe sandbank. SPC = supercharger

Sorry for bad english = C/P from Asian website

 

'91 KS4A Sambar Truck

Anyone know the cross reference for the rear wheel cylinders?

 

Possible part # for KS3/ KS4/ KV3/ KV4 wheel cylinder
Miyaco WC-F169 / RBC025 - should work for both sides
Unknown OEM part # at this time

 

Brake shoes

Has anyone found a brake shoe crossover?

 

More Part #'s

Valve Cover Gasket

Aftermarket Brand Name: Musashi

Part #: TP9011K, includes the following:

Musashi Part# TPS201 Moulded Valve Cover Gasket
Note: This part is equal to OEM #
13294-KA210
13294-KA100
13294-KA101
13294-KA102
13294-KA103
13294-KA190
13294-KA191

Musashi Part# TPS202 [6 O-Rings to seal valve cover bolts]
Note: This part is equal to OEM #
8069 11030
8069 11010

So just to be clear TP9011K = TPS201 + TPS202

Works for: KS3/4, KV3/4, TT1/2, TV1/2, TW1/2

---------------------------------------------------------------------

Subaru OEM distributor cap & rotor for KS4 S/C
Part # 22162KA140 - screw hold down with side plug tower for S/C
****This is a different cap than used for N/A models*******
Note: They also make this cap in a clip hold down - make sure you know
which style you have.

Subaru OEM points Part # 22186KA030 -points only, no condensor
Should work for KS3/4, KV3/4 and maybe others
Point Gap: .010"

-----------------------------------------------------------------------

Water Pump

Aftermarket Brand Name: Paraut

Paraut Part #: F3-021

Replaces OEM Part #'s:
21111-KA132
21111-KA192
21111-KA290
21111-KA291

Works For: KS3/4, KV3/4 - EN07 Engine 90.3~98.12

 

Sambar suspension

Has anyone found a cross reference for front struts and rear shocks for a KS4?

 

No but last time I was in Japanoid [Japanoid.com] the parts guy told me they ain't cheap - front struts $$$$

 

Great post this

Looking at replacing the distributor cap ( clips both sides, no screw fixing)and rotor arm to bottom out a problem, any ideas on part number cross references/ same bits fitted to other models out there?

Thanks

 

I currently have 4 Subarus, I've owned since last July. My partner and I are listing all the little things that need to be done for complete trouble free operation from the start.
After all we are building an Auto industry.

 

I will post part numbers we match through our local auto supply when gathered.
Best Regards, Love Subarus

 

Hi Folks,
Does anyone know if there is a universal split cv boot for a 1996 sambar
Thanks

 

Oil filter

'94 KS4 Sambar
Fram oil filter part number PH6607

 

1990 KS4 4WD EN07 motor, NON supercharged
Distributor cap BWD C605P - firing order is different on cap, actual order is 1, 3, 2, 4 and breather is in the 6 o'clock position
Fuel Filter Wix 33204- remove left rear wheel, its on the front side of the wheel behind the motor. Don't need to remove any bolts, it slides right out. New inlet/outlet on filter is slightly larger than stock, no fuel line retainer clips needed.
Ignition coil BWD E554P - requires using spade plugs rather than the factory connector
Ignition coil condenser BWD G124P - requires modifying the keeper bracket
Ignition coil resistor Napa ICR37
Direct fit, no trim air filter - Wix 46227
Front brake rotors - Wearever YH141258 - requires shaving about 1/8" off the diameter for proper fitment
Oil filter Purolater PL14610, uses 3 liters, or appx 3 quarts

Supercharged EN07Y
Spark Plugs - NGK BKR6EIX-11 (part number 3764)
Oil filter Purolater PL14610, uses 3 liters, or appx 3 quarts
Thermostat (may be the same for EN07 non-SC) Carquest 13758 with Fel-Pro 35292 gasket/o-ring

 

I have a new clutch disc I'd sell reasonable.

 

I have subaru sambar. Engine EN07. Its oil dip stick is broken. what is the length of oil dip stick?

 

Just sold mine last week, I'll have another late March I can answer you then

 

20 3/4 inches inside the tube and 23 inches overall. I tried to post a picture but the file was too big.

 

Thank You J.Bishop

 

I just found an after market spark plug set that snaps right in to my 1993 Sambar. They are NAPA Mileage Plus part number 4793. Only $24 at local NAPA store. The computer there says they are for some Nissan.

 

I'm in need of a front outer CV boot for my 1994 Subaru Sambar KS4. I've tried two different sets of boots off eBay that said they fit the Sambar with no luck. Does any other vehicle outer CV boot cross over? Surely, there is one on the shelf at a local parts store that will work?

 

So after trying two different sets of CV boots off eBay that was supposed to fit the Sambar I had to get creative and find a set that actually fit. I searched every CV boot made that met the measurements I took off of my front outer CV and axle and I finally found one that fit. The other good news is that it is listed on Amazon and is only $13!

All Balls 19-5006 Black 19mm x 66mm x 92mm Long CV Boot Kit: https://www.amazon.com/All-Balls-19...e=UTF8&qid=1505859754&sr=1-1&keywords=19-5006

I got it installed, did a short test ride and everything looks good and tight! I will report back if there are any issues after a long-term test.

 

So are you still happy with these? Looks like I am going to need to replace mine.

 

I haven't looked under the truck lately since it hasn't given me a reason to look. Everything seems to be working well. I will try and take a peek in the next day or so and report back if there are any issues.

 

Just replaced my rear wheel cylinders on my 1996 KS4. I used wheel cylinders made for a 1994 Subaru Justy. All of the mounting holes and thread sizes matched. They were about 1/16" longer than the originals but they worked great. My old cylinders were sticking causing the automatic adjusters to set my brakes too tight.

 

Attached is a PDF with the part numbers of the coolant lines and a few of the vacuum lines I replaced on my 1996 KS4. Thanks to rkrenicki on getting me the initial list and getting me started.

I removed the bed to replace the hoses. Replaced 24 coolant lines, and 15 vacuum lines and 9 fuel lines. Some of the simple straight coolant lines, fuel and vacuum lines are not on the list. You will need several different sizes of heater hose, (5/16”, 1/2,” 3/8”), several different sizes of fuel hose, (3/8”, 3/16”, 1/4”, 5/8”) and a couple of sizes of vacuum line, (5/32”, 1/4”). When you look up you own part numbers make sure you look at both the coolant diagram and water pump diagram, to get your part numbers. I also would buy the tee fitting listed for the engine coolant hoses, mine was brittle and broke when I removed the hoses. I've orderd a Gates #24710 hose to replace the filler neck hose but it has not arrived yet. (11/16/18, Hose worked great, had to cut off some from both ends)

It took me two full days to remove the bed and replace all the hoses. The OEM hoses I ordered from Japan ,except for the two bulk and the one Masterpro, and with shipping they were about $300. Along with a few trips to the local auto parts store for bulk hose. (another $50)

 

Bravo. That sounds like an extended migraine!

 

I did have a couple of adult beverages at the end of each day.

 

I have been maintaining an extensive spreadsheet of every part I have looked up for my truck, along with dealer pricing, Cross references, aftermarket part numbers, and US availabiltity. Some parts are specific to the 1992 KS4 Supercharged Model, but many are generic to the series.

I have it on Google Drive, and it can be found here: https://docs.google.com/spreadsheets/d/1mASg41uyMmMQCKHPuEAaKd6tTgOhHdlgUGOQIc_ojwo/edit?usp=sharing