1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

What did you do to your truck today?

Discussion in 'General Truck Info' started by Coast Steve, Aug 25, 2010.

  1. Smokie

    Smokie Member

    Thank you
     
  2. Bowe

    Bowe Member

    Today I modidfied the throttle bracket on my cv40 carb to accept the stock Minicab cable. Small step but necessary. 20A2A742-0ABB-4BBB-9577-5FFDCF6E11BD.jpeg
    8149A5CD-C2B1-432E-8FA3-1DAF0C48A391.jpeg
     
  3. kevin white

    kevin white New Member

    318093989_699077594879287_3388085367459987502_n.jpg 318197348_5982344055162674_7848271158491346520_n.jpg 318284276_886726035817287_3741640949038312115_n.jpg 315906071_831034004850034_6801185999025223282_n.jpg I have 225# coil springs on order through Summit Racing and want to raise the back 1". I made these rear shackles today, which are 2" longer. I was able to press out the o.e.m. shackle pins and press into the new shackles. Glad I measured both pins. I used a 1/2" drill bit for the top hole and a 35/64 for the bottom hole, then filed to have a crush fit. I am going to retain the 145r12 tire size and believe I'll order some Toyo's for it. Happy with the progress.
     
    Kevin in NC likes this.
  4. Liberty4Ever

    Liberty4Ever Active Member

    What did I do to my truck today? I picked it up at Newport News Marine Terminal and trailered it home. I drove 11 hours to the port last night in pitch black and dense fog on the very mountainous West Virginia Turnpike and I-64 in western Virginia, slept 1.5 hours in my truck, met the TWIC escort at the port at 7:30 AM, loaded the truck and drove home 11 hours in the rain. I'm getting too old for this stuff.

    Get a low boy trailer (no sides) and long ramps if you can. My Hijet has 4WD low ratio so I thought it'd crawl up into the 6X12 U-Haul trailer with a ramp. Nope. The little wheels hit the steep ramp and stopped. I had to race the engine and the clutch seems messed up and would only engage at the very end of the pedal release and even then it'd slip. It may need a new clutch. I'll know more when I off load the truck tomorrow, but I wasn't able to drive it onto the trailer. It would go if I popped the clutch to overcome the initial bump against the steep ramp, but that was a very committed move considering there's half an inch of clearance on the sides of the trailer. I had a 3500 pound boat winch in my truck that I use in lieu of a winch for emergency off road recovery and I was able to slowly winch the truck onto the trailer as one port guy steered and the other spotted. If you use a 6X12 U-Haul trailer, bring a hand winch or come along, as well as a jump box for dead batteries, jumper cables just in case, and a gallon of gas.

    I picked Newport News as my port of entry because I thought they might be easier given they're a smaller port. Everyone at the port was very nice and they only wanted my delivery order, which is essentially a form I made myself (as the importer) to give to myself (as the shipper). Customs all cleared before I got there thanks to the online broker. I had good luck with Eezyimport.com. I paid them $117.61 to file the paperwork. It's both a ripoff because I should be able to file my own paperwork with Customs, DOT and EPA, but also worth every penny because I spent a lot of time looking and found the forms everywhere but never found any examples of how to fill out the forms and more importantly, never found how to file them with the respective agencies. I think the forms can be emailed but the email addresses are a big damned secret. The bureaucrats really push us to use a customs broker.

    If you're importing through Newport News, I highly recommend Kurt (The Gandyman) at Crown TWIC Port Escort Services. He's awesome. I resent the DHS making us hire escorts to get on a terminal, but even if it wasn't required, having been through the process I'd still pay Kurt to do his magic. It ran as smoothly as possible, and it would have been a nightmare if I tried to visit the port by myself. I estimate a 50% chance of me being arrested. I'm a nice guy but bureaucrats do not like me and it goes downhill from there. Kurt saved me from that miserable fate.

    I have pictures but I'm too tired to post them... and you guys have seen a Hijet in a U-Haul trailer before.

    After a good night's sleep, tomorrow I'm going to unload the truck, return the U-Haul trailer, buy Hijet insurance and hopefully drive the truck to the sheriff for a VIN inspection and then the county clerk to title it, register it, pay taxes and get a license plate, then stop at the mom & pop hardware store to see if I can get a few spare keys for the Hijet (an old Toyota truck blank?) as well as key copies for my motorcycle and 4Runner.

    Then I'm going to start a LOT of little Hijet projects. Should be fun!

    The economics of JDM trucks is weird. I paid $265 for the truck, but it cost a total of $2380 including having it shipped to the port. $118 to the customs broker to file the government forms and another $30 to witness and notarize the power of attorney for the broker. $69 customs duty and fees (paid through the broker). $231 in port related expenses. $352 to drive to the port and trailer the truck home from 560 miles away. $62 to the state to get it licensed. That's $3240 so far to get it on the road, not including liability insurance, repairs, upgrades, upgrades, add-ons and upgrades. After I dump $2000 more in improvements, it'll be a sweet little 4WD truck, and even including the sweat equity it's probably a good investment based on the selling prices I'm seeing lately on some of these little trucks.
     
    Last edited: Dec 18, 2022
    Drain and Kevin in NC like this.
  5. kevin white

    kevin white New Member

    Today, I installed the 225# springs and mounted up the Toyo tires. Pretty happy with the way it looks. The shackles I made and the new springs raised it 1" all the way around. The tires look good. Even at 1" lift, I think I'll have to change the pinion angle a bit. It also has a little positive camber in front. I'm going to shim the rearend to correct the angle and consider slotting the body a bit at the strut mount to correct the camber. It won't take much. Pretty happy with the results. 317706938_5870147186378059_677554649524139543_n.jpg 317706938_5870147186378059_677554649524139543_n.jpg
     

    Attached Files:

    Liberty4Ever likes this.
  6. kevin white

    kevin white New Member

    The dash seems dark on these driving at night. Since there are no backlights on the heater controls, I put an led light under the passenger side of the dash. I found a wire that's only hot when the headlights are on and tied into it. 319368670_1119784395391197_4078013710413787870_n.jpg 320918941_5702086723243545_494413109969325439_n.jpg 319379942_564951198298843_8076671132557186520_n.jpg
     
    Liberty4Ever likes this.
  7. Liberty4Ever

    Liberty4Ever Active Member

    I did my first oil change on my 1996 Hijet today, including an engine flush and installing a Fumoto F-133 oil drain valve to make future oil changes quick, easy and less messy. All of the gory and glorious sexy fun details are on today's entry on my Hijet project page.

    https://minitrucktalk.com/threads/hijet-renovation-upgrade-project.22332/#post-130806

    Short story: Everything went well. No cussing or nuthin'.

    Next Hijet project: Replace existing incandescent bulbs with LED lights.
     
    t_g_farrell likes this.
  8. Jigs-n-fixtures

    Jigs-n-fixtures Well-Known Member

    Plugged him in to shore power. Forecast is for -20F tonight. High tomorrow of -1. With him plugged in and the heat pads warming things up, he should start pretty easy tomorrow.
     
    Limestone and Liberty4Ever like this.
  9. Liberty4Ever

    Liberty4Ever Active Member

    I changed the windshield washer fluid. :D

    The forecast is for -5 for an overnight low and a few days of bitter cold. I recently brought my Hijet home from the port and it had the windshield washer fluid from Japan in there, and I don't know what they use. It was blue and smelled very faintly of alcohol, but that may have been a mild detergent. The Japanese have little fizzy tablets that can be added to water to make "windshield washer fluid".

    https://www.amazon.com/s?k=windshield+fluid+tablet

    I started the truck, held down the windshield washer switch and quickly emptied the nearly full windshield washer fluid reservoir. I dumped in the Rain-X -20F washer fluid and ran the washer pump until the orange stuff was spraying on the windshield so I was confident that none of the windshield washer system, including the pump, would be freeze damaged tonight.

    Now I need to figure out why the windshield sprayer on the passenger side isn't spraying.

    I finally ran the Hijet engine enough to see the temperature gauge indicate that it was warming up. There was plenty of heat out the vents but the gauge never read over 1/3 of full scale. My wife's RAV4 is suddenly doing the same thing. Maybe a stuck open thermostat. Hopefully not a water pump.
     
  10. Jigs-n-fixtures

    Jigs-n-fixtures Well-Known Member

    Well he started just fine in the morning. In the afternoon when he had sat for ten hours, at just above zero, it was a bit hard to get started, and the cold lube in the tranny took a while to warm up to the point he would shift ok.
     
  11. Bowe

    Bowe Member

    Today I got my new timing belt and tensioner so I got that job wrapped up. Replaced wp, thermostat and alt/fan belt while I was at it. Also plugged the hole on intake for temperature vacuum switch and made block off plate for egr. Glad I blew radiator out as well, was holding lots of dirt.
     
    Last edited: Dec 27, 2022
  12. kevin white

    kevin white New Member

    I installed a set of grab handles from an '80 to '95 Samuri I ordered from Ebay. They are located differently than the Carry, but are usable. For $17, I'm surprised they don't seem to be used much. They bolted right up to the existing holes. 322959538_1595663790875646_64180928792232705_n.jpg
     
  13. t_g_farrell

    t_g_farrell Active Member

    So used the existing holes with no mods? Got the ebay link? Looks good.
     
  14. kevin white

    kevin white New Member

    No mods! They bolt directly up to the existing holes and came with the screws. Just look up suzuki samurai grab handle on Ebay and dozens will pop up. Samurai, Drover, Sierra, all work.
     
    t_g_farrell likes this.
  15. Liberty4Ever

    Liberty4Ever Active Member

    I did a lot of little things to my S110P Hijet today, including swapping the tail lights and brake lights to LED bulbs, cleaning and lubricating the heater flap control cable and linkage, measuring and ordering silicone vacuum lines, measuring so I can CAD and 3D print new door lock knobs, and installing a small fire extinguisher between the seat backs. The details including links to items used are in the latest post on my Hijet project page:

    https://minitrucktalk.com/threads/hijet-renovation-upgrade-project.22332/#post-131004
     
  16. Drain

    Drain Supporting Moderator Supporting Moderator Supporting Member

    I did my timing today. My 92 Sambar only has two timing marks, a zero and what I imagine is 5° since it was set just north of the top mark. Was idling a little low but I got to verify that my tach is correct :)
     
    bentresearch likes this.
  17. Drain

    Drain Supporting Moderator Supporting Moderator Supporting Member

  18. Tripthyme

    Tripthyme Active Member Supporting Member

    I ordered a spare guage cluster from Japan that I have gutted and about to install volt, gps speedometer, tachometer, fuel guages and indicator lights for turns and warnings
     
    Drain likes this.
  19. 39Lasalle

    39Lasalle New Member

    I had no turn signals or headlights, so I took the steering wheel off so I could get to the multi function switch. Took it apart on the work bench and cleaned the contacts. Works perfect now.

    39
     
    Liberty4Ever and Drain like this.
  20. t_g_farrell

    t_g_farrell Active Member

  21. bentresearch

    bentresearch New Member

    Recreated the center console end cap so I wouldn't have to drill holes in the OEM. I will upload the file once it has been properly tested.
    [​IMG]
    Holes used to mount the smallest CB radio I could find.
    [​IMG]
    [​IMG]
    Also got some new seat covers from 500yenshop.
    [​IMG]
     
    Last edited: Jan 13, 2023
    kevin white and Liberty4Ever like this.
  22. t_g_farrell

    t_g_farrell Active Member

    Drove from Charlotte, NC to DeLand, FL for the weekend in the wee van. Took ~11 hours each way using the secondary roads all the way. Via interstate its an 8 hour drive usually. No issues with the van other than a minor brake problem because I didn't tighten the right side caliper bracket good enough and it lost a bolt. I was able to move the upper bolt to the lower position and continue on. When it lost the lower bolt the caliper would jump back against the wheel when the brakes were applied (very noisy and scary sounding). By moving it to the bottom, it just pushed closer to the rotor when applying the brakes and worked for the remainder of the trip (9 hours of it). Once in FL I just got a bolt that would work and refastened the upper and drove home yesterday. Adventures are fun!
     
  23. Kevin in NC

    Kevin in NC Member Supporting Member

    Today I used my Suzuki dump truck as a dump truck rather than just using it as a butt buggy. I used my little Kubota loader to put 4 buckets of dirt/gravel mix into the bed of the Suzuki, then trundled off into the woods to dump it in a low spot on one of my trails. I'm not sure how much the load weighed but I guess each bucket from the Kubota is maybe 200 pounds or so.
    The truck handled the load just fine running in 4wd low, 1st and 2nd gear. The dump bed had no trouble rising up and dumping. It was a helluva lot easier than driving the tractor way back into the woods and dumping one bucket at a time.
    Kevin in NC kubota dump.jpg dirt load.jpg kubota dump.jpg dirt load.jpg
    kubota dump.jpg
     
  24. kevin white

    kevin white New Member

    I've been working on a rear bumper. It shouldn't take much to finish it up. 326786881_904845760669750_6190144282715133306_n.jpg 326320700_573890831273015_3861658415807095412_n.jpg 326798466_1566821703761864_6660858562899347512_n.jpg
     
    Liberty4Ever likes this.
  25. t_g_farrell

    t_g_farrell Active Member

  26. GeoJoe

    GeoJoe Member

    After filling sinkholes and hauling firewood to be split, I changed both front diff and transmission fluids, both which were way more lighter and honey colored than I would have thought. Minimal shavings on the magnetic transmission drain plug.

    [​IMG]

    [​IMG]

    [​IMG]
     
    Drain, Kevin in NC and Liberty4Ever like this.
  27. Kevin in NC

    Kevin in NC Member Supporting Member

    Mini trucks are a lot of fun. I have fun with my truck but it's nice to see posts here where forum members use their trucks for work. After all, these toys of ours were built as work trucks.
    Kevin in NC
     
  28. Drain

    Drain Supporting Moderator Supporting Moderator Supporting Member

    Same, this was last week but I figured out I can haul 1/4 cord of wood. :)

    [​IMG]
     
    bentresearch and Kevin in NC like this.
  29. kevin white

    kevin white New Member

    Finished up the bumper today. Should do the trick 329603764_1231170654159272_8016976042970108932_n.jpg
     
  30. Kauai Kei

    Kauai Kei Member

    PXL_20230215_011809507.jpg

    Speaking of bumpers.... I didn't make this, just bought it from Mini4x4.ca and installed it last night. Ignore the rust, dents, dodgy paint, etc. :)
     

Share This Page